Garmin G1000 Mooney M20TN User Manual Page 27

  • Download
  • Add to my manuals
  • Print
  • Page
    / 494
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 26
Garmin G1000 Pilot’s Guide for the Mooney M20M/M20R/M20TN
190-00647-01 Rev. B16
SYSTEM OVERVIEW
SYSTEM
OVERVIEW
FLIGHT
INSTRUMENTS
EIS
AUDIO PANEL
& CNS
FLIGHT
MANAGEMENT
HAZARD
AVOIDANCE
AFCS
ADDITIONAL
FEATURES
APPENDICESINDEX
BRG1
Cycles the Bearing 1 Information Window through NAV1, GPS/ waypoint identifier and GPS-
derived distance information, and ADF/frequency.
HSI FRMT
Displays the softkeys for selecting the two HSI formats
360 HSI
Displays HSI as a 360° compass rose
ARC HSI
Displays HSI as a 140° viewable arc
BRG2
Cycles the Bearing 2 Information Window through NAV2 or GPS waypoint identifier and GPS-
derived distance information, and ADF/frequency.
ALT UNIT
Displays softkeys for setting the altimeter and BARO settings to metric units
METERS
When enabled, displays altimeter in meters
IN
Press to display the BARO setting as inches of mercury
HPA
Press to display the BARO setting as hectopacals
STD BARO
Sets barometric pressure to 29.92 in Hg (1013 hPa if metric units are selected)
OBS
Selects OBS mode on the CDI when navigating by GPS (only available with active leg)
CDI
Cycles through GPS, VOR1, and VOR2 navigation modes on the CDI
ADF/DME Displays/removes ADF/DME Radio Tuning Window (optional; may appear as blank, ADF,
DME, or ADF/DME depending on installation)
BACK
Press the OFF or BACK Softkey to
return to the top-level softkeys.
DCLTR
DCLTR-2
DCLTR-3
DCLTR-1
TOPO
ALERTS
NEXRAD
(optional)
TERRAIN
XM LTNG
(optional)
OFF
INSET
INSET
XPDR
IDENT
TMR/REF
NRST
ALERTS
OBS
PFD
CDI
ADF/DME
(optional)
Press the CDI Softkey to cycle through
navigation sources:
- GPS
- NAV1 (VOR/LOC)
- NAV2 (VOR/LOC)
BRG2
STD BARO
BACK
ALERTS
HSI FRMT
PFD
BRG1
ALT UNIT
DME
(optional)
Press the BRG1/BRG2 softkeys to display/
remove the Bearing Information windows
and cycle through bearing sources:
- NAV1/NAV2
- GPS
- ADF
Press the STD BARO or BACK Softkey
to return to the top-level softkeys.
Press the BACK Softkey to return
to the top-level softkeys.
Press the IDENT or BACK Softkey
to return to the top-level softkeys.
XPDR
STBY
ON
ALT
VFR
IDENT
BACK
ALERTS
CODE
IDENT
BACK
ALERTS
0
1
2
3
4
5
6
7
BKSP
TRFC-1
TRFC-2
STRMSCP
(optional)
DFLTS WIND
GND
Figure 1-15 PFD Configuration Softkeys
XPDR Displays transponder mode selection softkeys:
STBY Selects standby mode (Transponder does not reply to any interrogations)
ON Selects Mode A (Transponder replies to interrogations)
ALT Selects Mode C – altitude reporting mode (Transponder replies to identification and altitude
interrogations)
GND
Manually selects Ground Mode, the transponder does not allow Mode A and Mode C
replies, but it does permit acquisition squitter and replies to discretely addressed Mode S
interrogations
VFR Automatically enters the VFR code (1200 in U.S.A. only)
Page view 26
1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 493 494

Comments to this Manuals

No comments