Garmin GPSMAP 7407 Installation Manual download pdf

GPSMAP

7400/7600

Series

Installation Instructions

Important Safety Information

WARNING

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

When connecting the power cable, do not remove the in-line

fuse holder. To prevent the possibility of injury or product

damage caused by fire or overheating, the appropriate fuse

must be in place as indicated in the product specifications. In

addition, connecting the power cable without the appropriate

fuse in place will void the product warranty.

CAUTION

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite

side of the surface.

To obtain the best performance and to avoid damage to your

boat, install the device according to these instructions.

Read all installation instructions before proceeding with the

installation. If you experience difficulty during the installation,

contact Garmin

Product Support.

Registering Your Device

Help us better support you by completing our online registration

today.

• Go to http://my.garmin.com.

• Keep the original sales receipt, or a photocopy, in a safe

place.

Contacting Garmin Product Support

• Go to www.garmin.com/support for in-country support

information.

• In the USA, call 913-397-8200 or 1-800-800-1020.

• In the UK, call 0808 238 0000.

• In Europe, call +44 (0) 870 850 1241.

Software Update

You may need to update the device software when you install

the device or add an accessory to the device.

Loading the New Software on a Memory Card

Insert a memory card into the card slot on the computer.

Go to www.garmin.com/support/software/marine.html.

Select Download next to "Garmin Marine Network with SD

card."

Read and agree to the terms.

Select Download.

Select Run.

Select the drive associated with the memory card, and select

Next > Finish.

Updating the Device Software

Before you can update the software, you must obtain a

software-update memory card or load the latest software onto a

memory card.

Turn on the chartplotter.

After the home screen appears, insert the memory card into

the card slot.

NOTE: In order for the software update instructions to

appear, the device must be fully booted before the card is

inserted.

Follow the on-screen instructions.

Wait several minutes while the software update process

completes.

The device returns to normal operation after the software

update process is complete.

Remove the memory card.

NOTE: If the memory card is removed before the device

restarts fully, the software update is not complete.

Tools Needed

• Drill and drill bits

◦ Bail mount: drill bits appropriate for the surface and

hardware

◦ Flush mount: 13 mm (

in.) drill bit, 7.2 mm (

in.), and

3.5 mm (

in.) drill bit

• #2 Phillips screwdriver

• Jigsaw or rotary tool

• File and sandpaper

• Marine sealant (recommended)

Mounting Considerations

NOTICE

This device should be mounted in a location that is not exposed

to extreme temperatures or conditions. The temperature range

for this device is listed in the product specifications. Extended

exposure to temperatures exceeding the specified temperature

range, in storage or operating conditions, may cause device

failure. Extreme-temperature-induced damage and related

consequences are not covered by the warranty.

Using the included hardware and template, you can mount the

device using one of two methods. You can use the included

bracket and hardware to bail mount the device, or you can use

the included template and hardware to flush mount the device in

the dashboard.

When selecting a mounting location, you should observe these

considerations.

• The location should provide optimal viewing as you operate

your boat.

• The location should allow for easy access to all device

interfaces, such as the keypad, touchscreen, and card

reader, if applicable.

• The location must be strong enough to support the weight of

the device and protect it from excessive vibration or shock.

• To avoid interference with a magnetic compass, the device

should not be installed closer to a compass than the

December 2014

Printed in Taiwan 190-01841-02_0A

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - 7400/7600

GPSMAP® 7400/7600 SeriesInstallation InstructionsImportant Safety Information WARNINGSee the Important Safety and Product Information guide in the pro

Page 2

compass-safe distance value listed in the product specifications.• The location must allow room for the routing and connection of all cables.Bail Moun

Page 3

21If you will have access to the back of the device, apply marine sealant around the cutout.22Place the device into the cutout.23Secure the device to

Page 4

• A Garmin Marine Network cable must be used for all Garmin Marine Network connections.◦ Third-party CAT5 cable and RJ45 connectors must not be used f

Page 5 - Specifications

Item DescriptionÀPower sourceÁPower cableÂHornÃLampÄNMEA 0183 cableÅRelay (100 mA coil current)ÆToggle switches to enable and disable lamp or horn ale

Page 6 - NMEA 0183 Information

Device Specification MeasurementTypical current draw at 12 Vdc1.8 AMax. current draw at 12 Vdc 2.3 ACompass-safe distance 310 mm (12.2 in.)Ten-inch mo

Page 7

Page 8

Garmin®, the Garmin logo, and GPSMAP® are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. These trademarks m

Comments to this Manuals

No comments

Garmin GPSMAP 7407 Installation Manual

Browse online or download Installation Manual for Navigators Garmin GPSMAP 7407. Garmin GPSMAP 7407 Installation Instructions User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Navigators Garmin GPSMAP 7407